Navoinics for iPad:
Connects to Raymarine NMEA and Seatalk streams via standard WiFi router
Upload/download waypoints and routes
No real-time instrument repeater
Navionics charts included in price
$35 USA. $50 USA & Canada
INavX:
Requires hardware such as iMux for WiFi and to translate Seatalk to NMEA – $250 approx
Supplied with NOAA raster charts. Navionics or others are addl $50 approx
Upload/download PLUS real-time instrument repeater capabilities
$50 with NOAA charts
I’d appreciate any corrections to the above. It would be nice to find out that the less expensive Navionics will repeat instruments, but I have not found any evidence of that.
Users report that iNavX has much better functionality overall. Even at $350 for the total package it is relatively inexpensive compared to the cost of an ST70 Multi repeater or a below decks chartplotter, assuming
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
If you are interested check out the forum at iphonesailing.com. That’s where I found the answers to many of my questions. Both the iNavX and Navionics users on that forum were very helpful in clarifying the hardware and software required to interface both apps to the E80. Also, there is much good info regarding the capabilities of each app.
Jeff Church
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
If there’s one thing I’ve learned, you can’t have a productive technical conversation based on fuzzy hypothetical options, and shifting objectives.
I can find no evidence that the mobile Navionics application “understands Seatalk”. What may be misleading is that the Raymarine Raytech RNS software, which “understands Seatalk without a mux”, uses Navionics charts. Brookhouse also stipulates the Program iNavx as a requirement for using their iMux combiner, again using Navionics charts. Navionics Mobile supports Plotter Sync which enables the wireless exchange of waypoint and route data. The following link is to a YouTube video by Raymarine which clearly demonstrates what is exchanged.
I don’t share the assessment that the Brookhouse iMux is for “somebody who is starting from scratch.” It was designed, built and is marketed to address the question and requirement you initially detailed…”Is it possible to access Seatalk information on an iPad thru its wifi connection and either
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
I did a little more research. Called Navionics and Raymarine.
Navionics says that their iPad app is primarily intended as a stand-alone app and told me to contact Ray regarding interfacing with a chartplotter. That seemed odd considering that Navionics developed Plotter Sync and incorporated it into their app less than a year ago as an interface to Raymarine plotters.
Ray says that they have “stepped away from Plotter Sync” because it was not reliable. I suspect that another reason might be that it competes with their new E7 chartplotter’s WiFi connect features.
My takeaway is that the Navionics app is probably useful as a nav tool and it MIGHT interface, but since I’m looking for an instrument repeater I’ll be looking at the iNavX app instead. iNavX is a bit more expensive, but it gets good reviews from folks who are using it as a plotter and real-time repeater
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
Some early Catalina 380″s may have void areas between the hull and the back of the refrigerators present insulation. Voids area will be found on both side as well as the frontal areas. Additional foam must be added to the bottom area, some sort of temporary cofferdam will be required in this area. The following procedure will increase the “R” value of the refrigerator.
Please Take Note:
This procedure will require great care in the drilling and injecting of the foam. Caution will be required when drilling thru the refrigerator outboard face to the void area. Drilling too deep will contact the hull or hull liner. Use caution when injecting this foam. It can become very messy stuff. Clean with lacquer thinner or acetone immediately. All drilled hoes to be 1/4″ diameter.
Step 1. Remove range
Step 2. Remove sole and sub sole in the area of
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
I wanted to share with all of you the outcome of the companionway hatch
cover that I wrote about a few weeks ago. Here is what I said at the time.
Mine, a 2000, hull 226, I guess is what Warren described as the “old” slider
version, which is all smoked acrylic. I have a similar problem –hatch
sticks and, depending on the weather, it is almost impossible to open and
close. Two companies in the yard (general maintenance and a fiberglass
expert) have looked at the hatch and the hatch frame and both concluded that
the “sticking” problem is caused by a structural problem with the framing.
According to both, the cabin hatch frame has a wood base that the hatch
frame screws into. According to one person who looked at the framing, a
certain amount of non-orthodox adjustments were made to build up the frame
to accommodate the
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
The cockpit table braces are Mobella part# MT-05-330-7, available from
www.southco.com for $19.95 each. To order, you need to telephone them at
321-638-4990.
The bridge clearance for my tall rig is 61′ 3″. My 380 specs say the standard rig is 4′ shorter than the tall rig. My clearance also includes a 2′ 7″ for a VHF antenna. So if have a typical sailboat VHF antenna. Your bridge clearance should be about 57′ 3″. If don’t have a VHF antenna then your wind vane is the tallest point and you can subtract another foot for a clearance of 56′ 3″. By the way I used 5′ 9″ for my water line to base of the mast measurement. I have the Charleston Spar conventional mast. All these dimensions were taken with the boat hauled and the mast unstepped.
Paul McManus
Sea Sea Rider C380 #185 Port Orchard, WA
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
I’ll chime in here as I have been doing a lot of research to upgrade my A/H. This is all Raymarine info, as I have no experience or knowledge on Furuno units.
I have a 1999 C380 with (factory?) installed ST6000 and a Type I linear drive (electric ball-screw type ram drive) mounted under the transom step and connected to an Edson arm (this part is readily available from Edson, and is specifically designed for linear drive units).
The ST6000 is an old unit with no other unit other than the control head, where all electrical connections are made. It does not handle heavy seas very well at all, and forget quartering seas. It will steer to a waypoint (if properly connected to a GPS), or a wind angle, as well as a simple compass course. It is a basic A/H.
The last (now retired)
You need to be logged in to see the rest of this content. Catalina380-IA members, please login.
To join please fill out a membership application (Association->Membership Application) and send a check to the address on the form.
